Description
This is the middle height of three in the Ruka range: a slim upright standing 60cm tall on a compact footprint, so it reads as a marker of light rather than a tall lamp to sit and read beneath. The body is anthracite, set against walnut, and the LED sits inside the housing rather than in a socket, so there is nothing to fit before switching on. It draws 13W and gives a warm white at 3000K, and it is not a dimming fitting: the light arrives at a fixed level. The sealed housing shrugs off dust and splashing water.
We would use it at low level, where light needs to fall on a surface rather than fill a room: beside a bench in a garden room, along a sheltered walkway, at the foot of a short flight of steps, or in a porch where a taller lamp would be in the way. The warm tone flatters brick, timber and painted walls, and the spread is wide enough to wash the ground close by. It suits anyone building light in layers, and it is one we often suggest in pairs where a path or terrace wants both sides lit.
The finish is a dark, even anthracite with walnut for contrast, chosen to sit quietly against planting and paving rather than pull the eye in daylight. Keep it clean by wiping the housing with a damp cloth, lifting grit off the walnut before it has a chance to mark, then drying the surface off. It carries a three year warranty. The same shape is made shorter and taller if this height is not the one you want, and there is a matching wall lamp in the range, including a version with a PIR motion sensor.
Specification
| Colour |
Anthracite |
| Second Colour |
Walnut |
| Weight |
3.10KG |
| Length |
220mm |
| Width |
125mm |
| Height |
600mm |
| Materials Used |
Die-cast Aluminium, Polycarbonate |
| Energy Class |
G |
| Energy Class of Lamp |
Group A |
| Max Energy Class |
G |
| Min Energy Class |
G |
| Lamp |
1 x 13W integrated LED (no lamps to fit) |
| Lamp Cap |
Integral LED |
| Recommended Lamp |
Integral LED |
| Colour Temperature |
3000K Warm White (±5%) |
| Number of Switching Cycles |
15000 |
| Average Life of LED |
30000hrs |
| LED Brand |
48LED 2835SMD |
| LED Power |
0.5W (±5%) |
| Type of LED |
SMD 2835 |
| Lumens per Watt (lm/W) |
65lm/W (±5%) |
| Beam Angle |
110° |
| System Flux |
850lm (±5%) |
| CRI |
>80 |
| Light Distribution |
Down |
| Driver Included |
Yes |
| Type of Driver |
Constant Current |
| Constant Current Output |
300mA |
| Min/Max. Voltage Output |
30-40V |
| Protection Class |
Class 1 - Earth Connection Required |
| Total Power Consumption |
13W (±5%) |
| Input Voltage |
100-240V~50/60Hz |
| Dimmable |
No |
| IP Rating |
IP54 |
| Average Life |
30000hrs |
| Warranty |
3yrs |
| UKCA/CE |
Yes |
| Pieces Included |
1 |
| Installation |
Requires Installation By Qualified Electrician |
| Product Care |
(1) Ensure light is not illuminated when cleaning. (2) Remove dirt with a damp cloth, do not use any detergents, do not clean with any pressurised water. |
| Country of Origin |
China |
Frequently Asked
How much light does it give out?
It produces 850 lumens from its 13W integrated LED, at 3000K warm white, with a wide 110 degree spread suited to lighting ground and nearby surfaces.
Can I put it on a dimmer?
No. It is a non-dimmable fitting and should be run on a standard switched circuit.
Is it protected against the weather?
It is rated IP54, so the housing resists dust and splashing water from any direction. It is a Class 1 fitting and requires an earth connection.
What are the dimensions and weight?
It stands 600mm high, 220mm long and 125mm wide, and weighs 3.1kg.
Will I ever need to replace the LED?
The LED is integrated and rated for an average life of 30,000 hours, so no lamp changes are involved.
How should I clean it?
A damp cloth on the anthracite housing and a light wipe over the walnut is enough. Avoid abrasive creams and solvents, and dry the surface rather than leaving it wet.