Description
A compact oblong outdoor wall light, finished in anthracite with an opal white diffuser across the front. The LED is built in and draws 10W, giving a warm white light that sits kindly against brick, render or painted timber. At 220mm wide it is small enough to flank a door in pairs, and the projection is shallow enough to stay clear of a narrow path. It is not dimmable and carries no switch of its own, so it runs from a wall switch on an outdoor circuit.
We would fit this at a front door, a back porch, or either side of a garage entrance where the light wants to be low, steady and unfussy. It is rated for outdoor use and copes with rain and splashing, which makes it a sensible choice for an exposed side passage or a garden wall. The warm tone suits older houses and dark brick well, and the fitting stays quiet in daylight. It is an earthed fitting and takes a fixed supply rather than a socket.
The housing is anthracite throughout, a grey-black that hides dust and weathers quietly, and the opal white diffuser is the only bright element on it. To keep it looking well, switch the power off, wipe the diffuser with a damp cloth at the end of winter when grit and cobwebs gather, then let it dry before you switch back on. Do the same for the body, avoiding scouring pads and solvents, which will dull the finish. It carries a three year warranty. The LED is integral, so there is nothing to swap out over its life. We keep it in anthracite, and it sits well beside plain house numbers and unpainted ironmongery.
Specification
| Colour |
Anthracite |
| Ceiling Mountable |
Yes |
| Weight |
5.60KG |
| Length |
220mm |
| Height |
108mm |
| Projection |
121mm |
| Materials Used |
Die-cast Aluminium, Polycarbonate |
| Adjustable Height |
No |
| Energy Class |
G |
| Max Energy Class |
G |
| Min Energy Class |
G |
| Lamp |
1 x 10W integrated LED (no lamps to fit) |
| Lamp Cap |
Integral LED |
| Recommended Lamp |
Integral LED |
| Colour Temperature |
3000K Warm White (±5%) |
| System Flux |
510lm (±5%) |
| Light Distribution |
Multiple Directions |
| Protection Class |
Class 1 - Earth Connection Required |
| Total Power Consumption |
10W (±5%) |
| Input Voltage |
220-240V~50/60Hz |
| Switch |
Not Switched |
| Dimmable |
No |
| IP Rating |
IP54 |
| Warranty |
3yrs |
| UKCA/CE |
Yes |
| Shade Colour |
Opal White |
| Shade Material |
PC |
| Shade Included |
Yes |
| Pieces Included |
1 |
| Installation |
Requires Installation By Qualified Electrician |
| Product Care |
(1) Wipe clean with a dry cloth, do not use any cleaning detergents, do not use rough or coarse material to clean. (2) Ensure light is not illuminated when cleaning. |
| Country of Origin |
China |
Frequently Asked
How bright is it?
It gives 510 lumens from a 10W integral LED, at 3000K warm white. That is a friendly doorway light rather than a floodlight, enough to read a keyhole and see a step clearly.
Can I dim it?
No. It is a non-dimmable fitting, so it should be run from a standard on/off switch rather than a dimmer.
What size is it?
It measures 220mm long by 108mm high, with a projection of 121mm from the wall face.
Is it suitable for a wall with no shelter above it?
Yes. It is rated IP54, so it tolerates rain and splashing on an open wall as well as under a porch.
Do I need to buy a bulb?
No. The LED is integrated within the fitting, so nothing is added and nothing is changed later.
How should I clean the opal diffuser?
Turn the power off, then use a damp cloth and a little mild detergent for grime or salt spray. Rinse the cloth, wipe again and let it dry fully before switching back on.