Description
A compact anthracite block that pushes light in two directions, up the wall and down it, through clear diffusers set at either end. At 10cm square it sits close and quiet against brickwork, render or timber cladding, and the warm white output reads soft rather than glaring once darkness falls. The LEDs are built in, so there is nothing to fit at the start and nothing to change later. There is no switch on the body, and it is not a dimming fitting, so it is happiest on a wall switch, a timer or a photocell somewhere on the circuit.
We would use one either side of a front door for a symmetrical welcome, or space several along a boundary wall to pick out a path or a set of steps without floodlighting the whole garden. The twin beams graze textured surfaces in a way a plain downward light cannot, so brick, flint and rough render all gain some depth after dark. It suits porches, side returns, garden rooms and courtyards, and the small footprint means it does not crowd a narrow passage or a low doorway. Warm white keeps the mood closer to a lit window than a car park.
The housing is sealed against rain and windblown dust, and the anthracite finish is a matt one that hides water spotting and settles happily alongside dark window frames and grey stonework. An earth connection is required. Cleaning is a job for the change of season: rinse the body with clean water, then wipe the diffusers so cobwebs, cut grass and road grit cannot dull either beam. It carries a three year warranty. We also stock the same fitting in a sand white for pale walls, and we tend to pair the two finishes across a house rather than mixing them on one elevation.
Specification
| Colour |
Anthracite |
| Ceiling Mountable |
Yes |
| Weight |
0.63KG |
| Length |
100mm |
| Width |
100mm |
| Projection |
100mm |
| Materials Used |
Aluminium Die-Casting Body, Glass Diffuser |
| Energy Class |
G |
| Max Energy Class |
G |
| Min Energy Class |
G |
| Lamp |
2 x 3W integrated LED (no lamps to fit) |
| Lamp Cap |
Integral LED |
| Recommended Lamp |
Integral LED |
| Colour Temperature |
3000K Warm White (±5%) |
| System Flux |
410lm (±5%) |
| Light Distribution |
Multiple Directions |
| Protection Class |
Class 1 - Earth Connection Required |
| Total Power Consumption |
7W (±5%) |
| Input Voltage |
220-240V~50/60Hz |
| Switch |
Not Switched |
| Dimmable |
No |
| IP Rating |
IP54 |
| Warranty |
3yrs |
| UKCA/CE |
Yes |
| Shade Colour |
Clear |
| Pieces Included |
1 |
| Installation |
Requires Installation By Qualified Electrician |
| Product Care |
(1) Ensure light is not illuminated when cleaning. (2) Remove dirt with a damp cloth, do not use any detergents, do not clean with any pressurised water. |
| Country of Origin |
China |
Frequently Asked
How much light does it give out?
Around 410 lumens in total from the two integrated LEDs, drawing 6W between them. That is a gentle pool of light above and below the fitting rather than broad general lighting.
What colour is the light?
3000K warm white, a soft yellow-toned light that suits brick, stone and painted render and keeps entrances looking welcoming.
Can I dim it?
No. It is a non-dimmable fitting, so it should be wired to a plain switch, a timer or a dusk-to-dawn control rather than a dimmer.
Will the LEDs need replacing?
The LEDs are integrated into the fitting, so there are no lamps to buy or change over its life.
How big is it and how far does it stand off the wall?
It measures 10cm high and 10cm wide, with a projection of 10cm, and weighs 0.63kg.
Is it suitable for a coastal or exposed position?
It is rated IP54, so it copes with rain and windblown dust. In salt air we would rinse it with fresh water more often to keep the finish looking its best.