Free Delivery on all orders over £99*

40W Constant Voltage LED Driver 24V - Non-Dimmable

£2299
The RRP is the manufacturer's recommended retail price of the item.
109 In Stock - Ready to Ship
We are an Independent UK Company
Price match. Found it cheaper? Contact us
Trade Discount Available
Description

The Knightsbridge 24DC40 is a 40W constant voltage LED driver that converts 230V 50Hz mains input to a 24V DC output for powering LED strip lighting, tape lights and other low-voltage LED installations. The driver maintains a steady 24V output across varying loads up to 40W maximum, making it suitable for runs of LED tape where consistent brightness is required regardless of the length of the run.

Designed for residential and commercial LED installations, the driver fits inside ceiling voids, under kitchen cabinets, behind coving or inside wardrobes where LED tape is being installed. The white polycarbonate housing measures 166mm long by 52mm wide by 24mm high, compact enough to fit in tight spaces but large enough to house the internal circuitry and heat management. Captured terminal screws on both input and output sides simplify wiring without needing separate terminal blocks.

The driver carries IP20 ingress protection, making it suitable for dry internal locations but not bathrooms, kitchens where splash contact is likely, or any outdoor application. Class II double-insulated construction means no earth connection is required. Built-in protections include open circuit (the driver shuts down if the load is disconnected), short circuit (shuts down if output wires touch), thermal overload (shuts down if internal temperature exceeds safe limits) and overload (shuts down if the connected LED load exceeds 40W). These protections reset automatically once the fault condition is removed.

This driver is non-dimmable. Attempting to dim the mains input with a standard phase-cut dimmer will cause flicker, noise or driver failure. For dimmable 24V LED installations, a compatible dimmable driver is required.

Specification
Length 166 mm
Height 24 mm
Width 52 mm
Construction Polycarbonate
Finish White
Class II
IP Rating IP20
Primary Voltage 230V 50Hz
Dimmable No
Driver Type Constant Voltage
Warranty 1
Downloads

Product Specification Sheet

Product Manual

Frequently Asked

What length of LED tape can this driver power?

That depends on the wattage per metre of the LED tape you're using. If your tape draws 8W per metre, this 40W driver can power up to 5 metres. If your tape draws 12W per metre, the driver can power approximately 3.3 metres. Check the LED tape specification for its power draw and divide 40W by that figure.

Can this driver be dimmed?

No. This is a non-dimmable driver. Installing it on a dimmed circuit will cause flicker, buzzing or driver failure. If dimming is required, a compatible dimmable LED driver must be used instead.

Where can the driver be installed?

The IP20 rating means the driver is suitable for dry internal locations only. Typical installations include inside ceiling voids above LED coving, under kitchen cabinets for plinth or under-cabinet tape lighting, inside wardrobes for LED shelf lighting, or behind false walls. Do not install in bathrooms, kitchens where splash contact is likely, or any outdoor location.

Does it need an earth connection?

No. The driver is Class II double-insulated, which means no earth connection is required. The mains input requires only live and neutral connections.

Shipping & Returns

Delivery UK delivery is £14.99, and delivery is free on all orders of £99 or more, in the UK and internationally.

Returns If you change your mind, you have 14 days from delivery to tell us, and a further 14 days to send the goods back. Return postage for a change-of-mind return is paid by you. Change-of-mind returns are subject to an inspection and handling deduction. See our full returns policy.

To arrange a return, call us on 020 8149 5199 or use our contact page.

See it lit, in person

Lighting looks different in a real room. Come and see our range at our showrooms in Birmingham, Hong Kong and Dubai, or talk to our design team wherever you are.

Niori lighting showroom trailer video with closeups of alabaster lighting

Why Niori

Over 20 years lighting homes worldwide

We are a specialist lighting and mirror retailer with showrooms in Birmingham, Hong Kong and Dubai, shipping to customers around the world. Our own design team is here to help, from first idea to final fitting.

Genuine products

An authorised stockist

Every product arrives brand new with the full manufacturer warranty. Found it cheaper elsewhere? Ask us about a price match.

Ordering with us

Free delivery over £99

Free delivery on orders over £99, in the UK and worldwide. Easy returns within 14 days, subject to our returns policy. Full manufacturer warranty included.

Design help

Not sure what you need?

Our design team can help you plan your lighting, share photos and videos of stock, and send samples worldwide. Book a showroom visit in Birmingham, Hong Kong or Dubai, or ask about our lighting design service.

You Might Also Like

Recommended For You

    Our Reviews

    From first click to final installation, our customers share how Niori lights up their spaces. Read their words and envision what’s possible for yours.

    Featured Projects

    Step into our portfolio and see how we transform homes, restaurants, and commercial spaces and more, worldwide. Click here for a closer look at our latest projects.

    Description

    The Knightsbridge 24DC40 is a 40W constant voltage LED driver that converts 230V 50Hz mains input to a 24V DC output for powering LED strip lighting, tape lights and other low-voltage LED installations. The driver maintains a steady 24V output across varying loads up to 40W maximum, making it suitable for runs of LED tape where consistent brightness is required regardless of the length of the run.

    Designed for residential and commercial LED installations, the driver fits inside ceiling voids, under kitchen cabinets, behind coving or inside wardrobes where LED tape is being installed. The white polycarbonate housing measures 166mm long by 52mm wide by 24mm high, compact enough to fit in tight spaces but large enough to house the internal circuitry and heat management. Captured terminal screws on both input and output sides simplify wiring without needing separate terminal blocks.

    The driver carries IP20 ingress protection, making it suitable for dry internal locations but not bathrooms, kitchens where splash contact is likely, or any outdoor application. Class II double-insulated construction means no earth connection is required. Built-in protections include open circuit (the driver shuts down if the load is disconnected), short circuit (shuts down if output wires touch), thermal overload (shuts down if internal temperature exceeds safe limits) and overload (shuts down if the connected LED load exceeds 40W). These protections reset automatically once the fault condition is removed.

    This driver is non-dimmable. Attempting to dim the mains input with a standard phase-cut dimmer will cause flicker, noise or driver failure. For dimmable 24V LED installations, a compatible dimmable driver is required.

    Specification
    Length 166 mm
    Height 24 mm
    Width 52 mm
    Construction Polycarbonate
    Finish White
    Class II
    IP Rating IP20
    Primary Voltage 230V 50Hz
    Dimmable No
    Driver Type Constant Voltage
    Warranty 1
    Downloads

    Product Specification Sheet

    Product Manual

    Frequently Asked

    What length of LED tape can this driver power?

    That depends on the wattage per metre of the LED tape you're using. If your tape draws 8W per metre, this 40W driver can power up to 5 metres. If your tape draws 12W per metre, the driver can power approximately 3.3 metres. Check the LED tape specification for its power draw and divide 40W by that figure.

    Can this driver be dimmed?

    No. This is a non-dimmable driver. Installing it on a dimmed circuit will cause flicker, buzzing or driver failure. If dimming is required, a compatible dimmable LED driver must be used instead.

    Where can the driver be installed?

    The IP20 rating means the driver is suitable for dry internal locations only. Typical installations include inside ceiling voids above LED coving, under kitchen cabinets for plinth or under-cabinet tape lighting, inside wardrobes for LED shelf lighting, or behind false walls. Do not install in bathrooms, kitchens where splash contact is likely, or any outdoor location.

    Does it need an earth connection?

    No. The driver is Class II double-insulated, which means no earth connection is required. The mains input requires only live and neutral connections.

    Shipping & Returns

    Delivery UK delivery is £14.99, and delivery is free on all orders of £99 or more, in the UK and internationally.

    Returns If you change your mind, you have 14 days from delivery to tell us, and a further 14 days to send the goods back. Return postage for a change-of-mind return is paid by you. Change-of-mind returns are subject to an inspection and handling deduction. See our full returns policy.

    To arrange a return, call us on 020 8149 5199 or use our contact page.